PageRenderTime 16ms CodeModel.GetById 11ms app.highlight 3ms RepoModel.GetById 1ms app.codeStats 0ms

/drivers/net/ethernet/seeq/sgiseeq.h

http://github.com/mirrors/linux
C Header | 104 lines | 82 code | 10 blank | 12 comment | 0 complexity | dd130aa598b806c8411c03f6c28d0e19 MD5 | raw file
  1/* SPDX-License-Identifier: GPL-2.0 */
  2/*
  3 * sgiseeq.h: Defines for the Seeq8003 ethernet controller.
  4 *
  5 * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
  6 */
  7#ifndef _SGISEEQ_H
  8#define _SGISEEQ_H
  9
 10struct sgiseeq_wregs {
 11	volatile unsigned int multicase_high[2];
 12	volatile unsigned int frame_gap;
 13	volatile unsigned int control;
 14};
 15
 16struct sgiseeq_rregs {
 17	volatile unsigned int collision_tx[2];
 18	volatile unsigned int collision_all[2];
 19	volatile unsigned int _unused0;
 20	volatile unsigned int rflags;
 21};
 22
 23struct sgiseeq_regs {
 24	union {
 25		volatile unsigned int eth_addr[6];
 26		volatile unsigned int multicast_low[6];
 27		struct sgiseeq_wregs wregs;
 28		struct sgiseeq_rregs rregs;
 29	} rw;
 30	volatile unsigned int rstat;
 31	volatile unsigned int tstat;
 32};
 33
 34/* Seeq8003 receive status register */
 35#define SEEQ_RSTAT_OVERF   0x001 /* Overflow */
 36#define SEEQ_RSTAT_CERROR  0x002 /* CRC error */
 37#define SEEQ_RSTAT_DERROR  0x004 /* Dribble error */
 38#define SEEQ_RSTAT_SFRAME  0x008 /* Short frame */
 39#define SEEQ_RSTAT_REOF    0x010 /* Received end of frame */
 40#define SEEQ_RSTAT_FIG     0x020 /* Frame is good */
 41#define SEEQ_RSTAT_TIMEO   0x040 /* Timeout, or late receive */
 42#define SEEQ_RSTAT_WHICH   0x080 /* Which status, 1=old 0=new */
 43#define SEEQ_RSTAT_LITTLE  0x100 /* DMA is done in little endian format */
 44#define SEEQ_RSTAT_SDMA    0x200 /* DMA has started */
 45#define SEEQ_RSTAT_ADMA    0x400 /* DMA is active */
 46#define SEEQ_RSTAT_ROVERF  0x800 /* Receive buffer overflow */
 47
 48/* Seeq8003 receive command register */
 49#define SEEQ_RCMD_RDISAB   0x000 /* Disable receiver on the Seeq8003 */
 50#define SEEQ_RCMD_IOVERF   0x001 /* IRQ on buffer overflows */
 51#define SEEQ_RCMD_ICRC     0x002 /* IRQ on CRC errors */
 52#define SEEQ_RCMD_IDRIB    0x004 /* IRQ on dribble errors */
 53#define SEEQ_RCMD_ISHORT   0x008 /* IRQ on short frames */
 54#define SEEQ_RCMD_IEOF     0x010 /* IRQ on end of frame */
 55#define SEEQ_RCMD_IGOOD    0x020 /* IRQ on good frames */
 56#define SEEQ_RCMD_RANY     0x040 /* Receive any frame */
 57#define SEEQ_RCMD_RBCAST   0x080 /* Receive broadcasts */
 58#define SEEQ_RCMD_RBMCAST  0x0c0 /* Receive broadcasts/multicasts */
 59
 60/* Seeq8003 transmit status register */
 61#define SEEQ_TSTAT_UFLOW   0x001 /* Transmit buffer underflow */
 62#define SEEQ_TSTAT_CLS     0x002 /* Collision detected */
 63#define SEEQ_TSTAT_R16     0x004 /* Did 16 retries to tx a frame */
 64#define SEEQ_TSTAT_PTRANS  0x008 /* Packet was transmitted ok */
 65#define SEEQ_TSTAT_LCLS    0x010 /* Late collision occurred */
 66#define SEEQ_TSTAT_WHICH   0x080 /* Which status, 1=old 0=new */
 67#define SEEQ_TSTAT_TLE     0x100 /* DMA is done in little endian format */
 68#define SEEQ_TSTAT_SDMA    0x200 /* DMA has started */
 69#define SEEQ_TSTAT_ADMA    0x400 /* DMA is active */
 70
 71/* Seeq8003 transmit command register */
 72#define SEEQ_TCMD_RB0      0x00 /* Register bank zero w/station addr */
 73#define SEEQ_TCMD_IUF      0x01 /* IRQ on tx underflow */
 74#define SEEQ_TCMD_IC       0x02 /* IRQ on collisions */
 75#define SEEQ_TCMD_I16      0x04 /* IRQ after 16 failed attempts to tx frame */
 76#define SEEQ_TCMD_IPT      0x08 /* IRQ when packet successfully transmitted */
 77#define SEEQ_TCMD_RB1      0x20 /* Register bank one w/multi-cast low byte */
 78#define SEEQ_TCMD_RB2      0x40 /* Register bank two w/multi-cast high byte */
 79
 80/* Seeq8003 control register */
 81#define SEEQ_CTRL_XCNT     0x01
 82#define SEEQ_CTRL_ACCNT    0x02
 83#define SEEQ_CTRL_SFLAG    0x04
 84#define SEEQ_CTRL_EMULTI   0x08
 85#define SEEQ_CTRL_ESHORT   0x10
 86#define SEEQ_CTRL_ENCARR   0x20
 87
 88/* Seeq8003 control registers on the SGI Hollywood HPC. */
 89#define SEEQ_HPIO_P1BITS  0x00000001 /* cycles to stay in P1 phase for PIO */
 90#define SEEQ_HPIO_P2BITS  0x00000060 /* cycles to stay in P2 phase for PIO */
 91#define SEEQ_HPIO_P3BITS  0x00000100 /* cycles to stay in P3 phase for PIO */
 92#define SEEQ_HDMA_D1BITS  0x00000006 /* cycles to stay in D1 phase for DMA */
 93#define SEEQ_HDMA_D2BITS  0x00000020 /* cycles to stay in D2 phase for DMA */
 94#define SEEQ_HDMA_D3BITS  0x00000000 /* cycles to stay in D3 phase for DMA */
 95#define SEEQ_HDMA_TIMEO   0x00030000 /* cycles for DMA timeout */
 96#define SEEQ_HCTL_NORM    0x00000000 /* Normal operation mode */
 97#define SEEQ_HCTL_RESET   0x00000001 /* Reset Seeq8003 and HPC interface */
 98#define SEEQ_HCTL_IPEND   0x00000002 /* IRQ is pending for the chip */
 99#define SEEQ_HCTL_IPG     0x00001000 /* Inter-packet gap */
100#define SEEQ_HCTL_RFIX    0x00002000 /* At rxdc, clear end-of-packet */
101#define SEEQ_HCTL_EFIX    0x00004000 /* fixes intr status bit settings */
102#define SEEQ_HCTL_IFIX    0x00008000 /* enable startup timeouts */
103
104#endif /* !(_SGISEEQ_H) */