/nucleo-f303RE/include/stm32f3xx_hal_conf.h
C Header | 341 lines | 159 code | 54 blank | 128 comment | 0 complexity | ce8b6200580002f76cf7e96f4716dbdb MD5 | raw file
Possible License(s): GPL-3.0
- /**
- ******************************************************************************
- * @file stm32f3xx_hal_conf.h
- * @brief HAL configuration file.
- ******************************************************************************
- * @attention
- *
- * <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
- /* Define to prevent recursive inclusion -------------------------------------*/
- #ifndef __STM32F3xx_HAL_CONF_H
- #define __STM32F3xx_HAL_CONF_H
-
- #ifdef __cplusplus
- extern "C" {
- #endif
-
- #include "mxconstants.h"
-
- /* Exported types ------------------------------------------------------------*/
- /* Exported constants --------------------------------------------------------*/
-
- /* ########################## Module Selection ############################## */
- /**
- * @brief This is the list of modules to be used in the HAL driver
- */
-
- #define HAL_MODULE_ENABLED
- #define HAL_ADC_MODULE_ENABLED
- //#define HAL_CAN_MODULE_ENABLED
- //#define HAL_CEC_MODULE_ENABLED
- //#define HAL_NAND_MODULE_ENABLED
- //#define HAL_NOR_MODULE_ENABLED
- //#define HAL_PCCARD_MODULE_ENABLED
- //#define HAL_SRAM_MODULE_ENABLED
- //#define HAL_HRTIM_MODULE_ENABLED
- //#define HAL_OPAMP_MODULE_ENABLED
- //#define HAL_SDADC_MODULE_ENABLED
- //#define HAL_TSC_MODULE_ENABLED
- //#define HAL_COMP_MODULE_ENABLED
- #define HAL_CRC_MODULE_ENABLED
- //#define HAL_CRYP_MODULE_ENABLED
- #define HAL_DAC_MODULE_ENABLED
- #define HAL_I2C_MODULE_ENABLED
- //#define HAL_I2S_MODULE_ENABLED
- //#define HAL_IWDG_MODULE_ENABLED
- //#define HAL_LCD_MODULE_ENABLED
- //#define HAL_LPTIM_MODULE_ENABLED
- //#define HAL_RNG_MODULE_ENABLED
- //#define HAL_RTC_MODULE_ENABLED
- #define HAL_SPI_MODULE_ENABLED
- #define HAL_TIM_MODULE_ENABLED
- #define HAL_UART_MODULE_ENABLED
- //#define HAL_USART_MODULE_ENABLED
- //#define HAL_IRDA_MODULE_ENABLED
- //#define HAL_SMARTCARD_MODULE_ENABLED
- //#define HAL_SMBUS_MODULE_ENABLED
- //#define HAL_WWDG_MODULE_ENABLED
- //#define HAL_PCD_MODULE_ENABLED
- #define HAL_GPIO_MODULE_ENABLED
- #define HAL_DMA_MODULE_ENABLED
- #define HAL_RCC_MODULE_ENABLED
- #define HAL_FLASH_MODULE_ENABLED
- #define HAL_PWR_MODULE_ENABLED
- #define HAL_CORTEX_MODULE_ENABLED
- /* ########################## HSE/HSI Values adaptation ##################### */
- /**
- * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
- * This value is used by the RCC HAL module to compute the system frequency
- * (when HSE is used as system clock source, directly or through the PLL).
- */
- #if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
- #endif /* HSE_VALUE */
-
- /**
- * @brief In the following line adjust the External High Speed oscillator (HSE) Startup
- * Timeout value
- */
- #if !defined (HSE_STARTUP_TIMEOUT)
- #define HSE_STARTUP_TIMEOUT ((uint32_t)100) /*!< Time out for HSE start up, in ms */
- #endif /* HSE_STARTUP_TIMEOUT */
-
- /**
- * @brief Internal High Speed oscillator (HSI) value.
- * This value is used by the RCC HAL module to compute the system frequency
- * (when HSI is used as system clock source, directly or through the PLL).
- */
- #if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)8000000) /*!< Value of the Internal oscillator in Hz*/
- #endif /* HSI_VALUE */
-
- /**
- * @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup
- * Timeout value
- */
- #if !defined (HSI_STARTUP_TIMEOUT)
- #define HSI_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSI start up */
- #endif /* HSI_STARTUP_TIMEOUT */
-
- /**
- * @brief Internal Low Speed oscillator (LSI) value.
- */
- #if !defined (LSI_VALUE)
- #define LSI_VALUE ((uint32_t)40000)
- #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
- The real value may vary depending on the variations
- in voltage and temperature. */
- /**
- * @brief External Low Speed oscillator (LSE) value.
- */
- #if !defined (LSE_VALUE)
- #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */
- #endif /* LSE_VALUE */
-
- /**
- * @brief Time out for LSE start up value in ms.
- */
- #if !defined (LSE_STARTUP_TIMEOUT)
- #define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */
- #endif /* LSE_STARTUP_TIMEOUT */
-
- /**
- * @brief External clock source for I2S peripheral
- * This value is used by the I2S HAL module to compute the I2S clock source
- * frequency, this source is inserted directly through I2S_CKIN pad.
- * - External clock generated through external PLL component on EVAL 303 (based on MCO or crystal)
- * - External clock not generated on EVAL 373
- */
- #if !defined (EXTERNAL_CLOCK_VALUE)
- #define EXTERNAL_CLOCK_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz*/
- #endif /* EXTERNAL_CLOCK_VALUE */
-
- /* Tip: To avoid modifying this file each time you need to use different HSE,
- === you can define the HSE value in your toolchain compiler preprocessor. */
-
- /* ########################### System Configuration ######################### */
- /**
- * @brief This is the HAL system configuration section
- */
-
- #define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */
- #define TICK_INT_PRIORITY ((uint32_t)0) /*!< tick interrupt priority (lowest by default) */
- #define USE_RTOS 0
- #define PREFETCH_ENABLE 1
- #define INSTRUCTION_CACHE_ENABLE 0
- #define DATA_CACHE_ENABLE 0
-
- /* ########################## Assert Selection ############################## */
- /**
- * @brief Uncomment the line below to expanse the "assert_param" macro in the
- * HAL drivers code
- */
- /* #define USE_FULL_ASSERT 1 */
-
- /* Includes ------------------------------------------------------------------*/
- /**
- * @brief Include module's header file
- */
-
- #ifdef HAL_RCC_MODULE_ENABLED
- #include "stm32f3xx_hal_rcc.h"
- #endif /* HAL_RCC_MODULE_ENABLED */
-
- #ifdef HAL_GPIO_MODULE_ENABLED
- #include "stm32f3xx_hal_gpio.h"
- #endif /* HAL_GPIO_MODULE_ENABLED */
-
- #ifdef HAL_DMA_MODULE_ENABLED
- #include "stm32f3xx_hal_dma.h"
- #endif /* HAL_DMA_MODULE_ENABLED */
-
- #ifdef HAL_CORTEX_MODULE_ENABLED
- #include "stm32f3xx_hal_cortex.h"
- #endif /* HAL_CORTEX_MODULE_ENABLED */
-
- #ifdef HAL_ADC_MODULE_ENABLED
- #include "stm32f3xx_hal_adc.h"
- #endif /* HAL_ADC_MODULE_ENABLED */
-
- #ifdef HAL_CAN_MODULE_ENABLED
- #include "stm32f3xx_hal_can.h"
- #endif /* HAL_CAN_MODULE_ENABLED */
-
- #ifdef HAL_CEC_MODULE_ENABLED
- #include "stm32f3xx_hal_cec.h"
- #endif /* HAL_CEC_MODULE_ENABLED */
-
- #ifdef HAL_COMP_MODULE_ENABLED
- #include "stm32f3xx_hal_comp.h"
- #endif /* HAL_COMP_MODULE_ENABLED */
-
- #ifdef HAL_CRC_MODULE_ENABLED
- #include "stm32f3xx_hal_crc.h"
- #endif /* HAL_CRC_MODULE_ENABLED */
-
- #ifdef HAL_DAC_MODULE_ENABLED
- #include "stm32f3xx_hal_dac.h"
- #endif /* HAL_DAC_MODULE_ENABLED */
-
- #ifdef HAL_FLASH_MODULE_ENABLED
- #include "stm32f3xx_hal_flash.h"
- #endif /* HAL_FLASH_MODULE_ENABLED */
-
- #ifdef HAL_SRAM_MODULE_ENABLED
- #include "stm32f3xx_hal_sram.h"
- #endif /* HAL_SRAM_MODULE_ENABLED */
-
- #ifdef HAL_NOR_MODULE_ENABLED
- #include "stm32f3xx_hal_nor.h"
- #endif /* HAL_NOR_MODULE_ENABLED */
-
- #ifdef HAL_NAND_MODULE_ENABLED
- #include "stm32f3xx_hal_nand.h"
- #endif /* HAL_NAND_MODULE_ENABLED */
-
- #ifdef HAL_PCCARD_MODULE_ENABLED
- #include "stm32f3xx_hal_pccard.h"
- #endif /* HAL_PCCARD_MODULE_ENABLED */
-
- #ifdef HAL_HRTIM_MODULE_ENABLED
- #include "stm32f3xx_hal_hrtim.h"
- #endif /* HAL_HRTIM_MODULE_ENABLED */
-
- #ifdef HAL_I2C_MODULE_ENABLED
- #include "stm32f3xx_hal_i2c.h"
- #endif /* HAL_I2C_MODULE_ENABLED */
-
- #ifdef HAL_I2S_MODULE_ENABLED
- #include "stm32f3xx_hal_i2s.h"
- #endif /* HAL_I2S_MODULE_ENABLED */
-
- #ifdef HAL_IRDA_MODULE_ENABLED
- #include "stm32f3xx_hal_irda.h"
- #endif /* HAL_IRDA_MODULE_ENABLED */
-
- #ifdef HAL_IWDG_MODULE_ENABLED
- #include "stm32f3xx_hal_iwdg.h"
- #endif /* HAL_IWDG_MODULE_ENABLED */
-
- #ifdef HAL_OPAMP_MODULE_ENABLED
- #include "stm32f3xx_hal_opamp.h"
- #endif /* HAL_OPAMP_MODULE_ENABLED */
-
- #ifdef HAL_PCD_MODULE_ENABLED
- #include "stm32f3xx_hal_pcd.h"
- #endif /* HAL_PCD_MODULE_ENABLED */
-
- #ifdef HAL_PWR_MODULE_ENABLED
- #include "stm32f3xx_hal_pwr.h"
- #endif /* HAL_PWR_MODULE_ENABLED */
-
- #ifdef HAL_RTC_MODULE_ENABLED
- #include "stm32f3xx_hal_rtc.h"
- #endif /* HAL_RTC_MODULE_ENABLED */
-
- #ifdef HAL_SDADC_MODULE_ENABLED
- #include "stm32f3xx_hal_sdadc.h"
- #endif /* HAL_SDADC_MODULE_ENABLED */
-
- #ifdef HAL_SMARTCARD_MODULE_ENABLED
- #include "stm32f3xx_hal_smartcard.h"
- #endif /* HAL_SMARTCARD_MODULE_ENABLED */
-
- #ifdef HAL_SMBUS_MODULE_ENABLED
- #include "stm32f3xx_hal_smbus.h"
- #endif /* HAL_SMBUS_MODULE_ENABLED */
-
- #ifdef HAL_SPI_MODULE_ENABLED
- #include "stm32f3xx_hal_spi.h"
- #endif /* HAL_SPI_MODULE_ENABLED */
-
- #ifdef HAL_TIM_MODULE_ENABLED
- #include "stm32f3xx_hal_tim.h"
- #endif /* HAL_TIM_MODULE_ENABLED */
-
- #ifdef HAL_TSC_MODULE_ENABLED
- #include "stm32f3xx_hal_tsc.h"
- #endif /* HAL_TSC_MODULE_ENABLED */
-
- #ifdef HAL_UART_MODULE_ENABLED
- #include "stm32f3xx_hal_uart.h"
- #endif /* HAL_UART_MODULE_ENABLED */
-
- #ifdef HAL_USART_MODULE_ENABLED
- #include "stm32f3xx_hal_usart.h"
- #endif /* HAL_USART_MODULE_ENABLED */
-
- #ifdef HAL_WWDG_MODULE_ENABLED
- #include "stm32f3xx_hal_wwdg.h"
- #endif /* HAL_WWDG_MODULE_ENABLED */
-
- /* Exported macro ------------------------------------------------------------*/
- #ifdef USE_FULL_ASSERT
- /**
- * @brief The assert_param macro is used for function's parameters check.
- * @param expr: If expr is false, it calls assert_failed function
- * which reports the name of the source file and the source
- * line number of the call that failed.
- * If expr is true, it returns no value.
- * @retval None
- */
- #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
- /* Exported functions ------------------------------------------------------- */
- void assert_failed(uint8_t* file, uint32_t line);
- #else
- #define assert_param(expr) ((void)0)
- #endif /* USE_FULL_ASSERT */
-
- #ifdef __cplusplus
- }
- #endif
-
- #endif /* __STM32F3xx_HAL_CONF_H */
-
- /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/