PageRenderTime 55ms CodeModel.GetById 24ms app.highlight 25ms RepoModel.GetById 1ms app.codeStats 0ms

#! | 504 lines | 387 code | 117 blank | 0 comment | 0 complexity | 702b1a1f6611e90b73f6ae768cb083a5 MD5 | raw file
Possible License(s): GPL-2.0, LGPL-2.0, AGPL-1.0
  2# wan devices configuration
  5menuconfig WAN
  6	bool "Wan interfaces support"
  7	---help---
  8	  Wide Area Networks (WANs), such as X.25, Frame Relay and leased
  9	  lines, are used to interconnect Local Area Networks (LANs) over vast
 10	  distances with data transfer rates significantly higher than those
 11	  achievable with commonly used asynchronous modem connections.
 13	  Usually, a quite expensive external device called a `WAN router' is
 14	  needed to connect to a WAN. As an alternative, a relatively
 15	  inexpensive WAN interface card can allow your Linux box to directly
 16	  connect to a WAN.
 18	  If you have one of those cards and wish to use it under Linux,
 19	  say Y here and also to the WAN driver for your card.
 21	  If unsure, say N.
 23if WAN
 25# There is no way to detect a comtrol sv11 - force it modular for now.
 26config HOSTESS_SV11
 27	tristate "Comtrol Hostess SV-11 support"
 28	depends on ISA && m && ISA_DMA_API && INET && HDLC
 29	help
 30	  Driver for Comtrol Hostess SV-11 network card which
 31	  operates on low speed synchronous serial links at up to
 32	  256Kbps, supporting PPP and Cisco HDLC.
 34	  The driver will be compiled as a module: the
 35	  module will be called hostess_sv11.
 37# The COSA/SRP driver has not been tested as non-modular yet.
 38config COSA
 39	tristate "COSA/SRP sync serial boards support"
 40	depends on ISA && m && ISA_DMA_API && HDLC
 41	---help---
 42	  Driver for COSA and SRP synchronous serial boards.
 44	  These boards allow to connect synchronous serial devices (for example
 45	  base-band modems, or any other device with the X.21, V.24, V.35 or
 46	  V.36 interface) to your Linux box. The cards can work as the
 47	  character device, synchronous PPP network device, or the Cisco HDLC
 48	  network device.
 50	  You will need user-space utilities COSA or SRP boards for downloading
 51 	  the firmware to the cards and to set them up. Look at the
 52	  <> for more information. You can also
 53	  read the comment at the top of the <file:drivers/net/wan/cosa.c> for
 54	  details about the cards and the driver itself.
 56	  The driver will be compiled as a module: the
 57	  module will be called cosa.
 60# Lan Media's board. Currently 1000, 1200, 5200, 5245
 62config LANMEDIA
 63	tristate "LanMedia Corp. SSI/V.35, T1/E1, HSSI, T3 boards"
 64	depends on PCI && VIRT_TO_BUS && HDLC
 65	---help---
 66	  Driver for the following Lan Media family of serial boards:
 68	  - LMC 1000 board allows you to connect synchronous serial devices
 69	  (for example base-band modems, or any other device with the X.21,
 70	  V.24, V.35 or V.36 interface) to your Linux box.
 72	  - LMC 1200 with on board DSU board allows you to connect your Linux
 73	  box directly to a T1 or E1 circuit.
 75	  - LMC 5200 board provides a HSSI interface capable of running up to
 76	  52 Mbits per second.
 78	  - LMC 5245 board connects directly to a T3 circuit saving the
 79	  additional external hardware.
 81	  To change setting such as clock source you will need lmcctl.
 82	  It is available at <> (broken link).
 84	  To compile this driver as a module, choose M here: the
 85	  module will be called lmc.
 87# There is no way to detect a Sealevel board. Force it modular
 88config SEALEVEL_4021
 89	tristate "Sealevel Systems 4021 support"
 90	depends on ISA && m && ISA_DMA_API && INET && HDLC
 91	help
 92	  This is a driver for the Sealevel Systems ACB 56 serial I/O adapter.
 94	  The driver will be compiled as a module: the
 95	  module will be called sealevel.
 97# Generic HDLC
 98config HDLC
 99	tristate "Generic HDLC layer"
100	help
101	  Say Y to this option if your Linux box contains a WAN (Wide Area
102	  Network) card supported by this driver and you are planning to
103	  connect the box to a WAN.
105	  You will need supporting software from
106	  <>.
107	  Generic HDLC driver currently supports raw HDLC, Cisco HDLC, Frame
108	  Relay, synchronous Point-to-Point Protocol (PPP) and X.25.
110 	  To compile this driver as a module, choose M here: the
111	  module will be called hdlc.
113	  If unsure, say N.
115config HDLC_RAW
116	tristate "Raw HDLC support"
117	depends on HDLC
118	help
119	  Generic HDLC driver supporting raw HDLC over WAN connections.
121	  If unsure, say N.
123config HDLC_RAW_ETH
124	tristate "Raw HDLC Ethernet device support"
125	depends on HDLC
126	help
127	  Generic HDLC driver supporting raw HDLC Ethernet device emulation
128	  over WAN connections.
130	  You will need it for Ethernet over HDLC bridges.
132	  If unsure, say N.
134config HDLC_CISCO
135	tristate "Cisco HDLC support"
136	depends on HDLC
137	help
138	  Generic HDLC driver supporting Cisco HDLC over WAN connections.
140	  If unsure, say N.
142config HDLC_FR
143	tristate "Frame Relay support"
144	depends on HDLC
145	help
146	  Generic HDLC driver supporting Frame Relay over WAN connections.
148	  If unsure, say N.
150config HDLC_PPP
151	tristate "Synchronous Point-to-Point Protocol (PPP) support"
152	depends on HDLC
153	help
154	  Generic HDLC driver supporting PPP over WAN connections.
156	  If unsure, say N.
158config HDLC_X25
159	tristate "X.25 protocol support"
160	depends on HDLC && (LAPB=m && HDLC=m || LAPB=y)
161	help
162	  Generic HDLC driver supporting X.25 over WAN connections.
164	  If unsure, say N.
166comment "X.25/LAPB support is disabled"
167	depends on HDLC && (LAPB!=m || HDLC!=m) && LAPB!=y
169config PCI200SYN
170	tristate "Goramo PCI200SYN support"
171	depends on HDLC && PCI
172	help
173	  Driver for PCI200SYN cards by Goramo sp. j.
175	  If you have such a card, say Y here and see
176	  <>.
178	  To compile this as a module, choose M here: the
179	  module will be called pci200syn.
181	  If unsure, say N.
183config WANXL
184	tristate "SBE Inc. wanXL support"
185	depends on HDLC && PCI
186	help
187	  Driver for wanXL PCI cards by SBE Inc.
189	  If you have such a card, say Y here and see
190	  <>.
192	  To compile this as a module, choose M here: the
193	  module will be called wanxl.
195	  If unsure, say N.
198	bool "rebuild wanXL firmware"
200	help
201	  Allows you to rebuild firmware run by the QUICC processor.
202	  It requires as68k, ld68k and hexdump programs.
204	  You should never need this option, say N.
206config PC300
207	tristate "Cyclades-PC300 support (RS-232/V.35, X.21, T1/E1 boards)"
208	depends on HDLC && PCI && BROKEN
209	---help---
210	  This driver is broken because of struct tty_driver change.
212	  Driver for the Cyclades-PC300 synchronous communication boards.
214	  These boards provide synchronous serial interfaces to your
215	  Linux box (interfaces currently available are RS-232/V.35, X.21 and
216	  T1/E1). If you wish to support Multilink PPP, please select the
217	  option later and read the file README.mlppp provided by PC300
218	  package.
220	  To compile this as a module, choose M here: the module
221	  will be called pc300.
223	  If unsure, say N.
225config PC300_MLPPP
226	bool "Cyclades-PC300 MLPPP support"
227	depends on PC300 && PPP_MULTILINK && PPP_SYNC_TTY && HDLC_PPP
228	help
229	  Multilink PPP over the PC300 synchronous communication boards.
231comment "Cyclades-PC300 MLPPP support is disabled."
232	depends on HDLC && PC300 && (PPP=n || !PPP_MULTILINK || PPP_SYNC_TTY=n || !HDLC_PPP)
234comment "Refer to the file README.mlppp, provided by PC300 package."
235	depends on HDLC && PC300 && (PPP=n || !PPP_MULTILINK || PPP_SYNC_TTY=n || !HDLC_PPP)
237config PC300TOO
238	tristate "Cyclades PC300 RSV/X21 alternative support"
239	depends on HDLC && PCI
240	help
241	  Alternative driver for PC300 RSV/X21 PCI cards made by
242	  Cyclades, Inc. If you have such a card, say Y here and see
243	  <>.
245	  To compile this as a module, choose M here: the module
246	  will be called pc300too.
248	  If unsure, say N here.
250config N2
251	tristate "SDL RISCom/N2 support"
252	depends on HDLC && ISA
253	help
254	  Driver for RISCom/N2 single or dual channel ISA cards by
255	  SDL Communications Inc.
257	  If you have such a card, say Y here and see
258	  <>.
260	  Note that N2csu and N2dds cards are not supported by this driver.
262	  To compile this driver as a module, choose M here: the module
263	  will be called n2.
265	  If unsure, say N.
267config C101
268	tristate "Moxa C101 support"
269	depends on HDLC && ISA
270	help
271	  Driver for C101 SuperSync ISA cards by Moxa Technologies Co., Ltd.
273	  If you have such a card, say Y here and see
274	  <>.
276	  To compile this driver as a module, choose M here: the
277	  module will be called c101.
279	  If unsure, say N.
281config FARSYNC
282	tristate "FarSync T-Series support"
283	depends on HDLC && PCI
284	---help---
285	  Support for the FarSync T-Series X.21 (and V.35/V.24) cards by
286	  FarSite Communications Ltd.
288	  Synchronous communication is supported on all ports at speeds up to
289	  8Mb/s (128K on V.24) using synchronous PPP, Cisco HDLC, raw HDLC,
290	  Frame Relay or X.25/LAPB.
292	  If you want the module to be automatically loaded when the interface
293	  is referenced then you should add "alias hdlcX farsync" to
294	  /etc/modprobe.conf for each interface, where X is 0, 1, 2, ..., or
295	  simply use "alias hdlc* farsync" to indicate all of them.
297	  To compile this driver as a module, choose M here: the
298	  module will be called farsync.
300config DSCC4
301	tristate "Etinc PCISYNC serial board support"
302	depends on HDLC && PCI && m
303	help
304	  Driver for Etinc PCISYNC boards based on the Infineon (ex. Siemens)
305	  DSCC4 chipset.
307	  This is supposed to work with the four port card. Take a look at
308	  <> for further information about the
309	  driver.
311	  To compile this driver as a module, choose M here: the
312	  module will be called dscc4.
314config DSCC4_PCISYNC
315	bool "Etinc PCISYNC features"
316	depends on DSCC4
317	help
318	  Due to Etinc's design choice for its PCISYNC cards, some operations
319	  are only allowed on specific ports of the DSCC4. This option is the
320	  only way for the driver to know that it shouldn't return a success
321	  code for these operations.
323	  Please say Y if your card is an Etinc's PCISYNC.
325config DSCC4_PCI_RST
326	bool "Hard reset support"
327	depends on DSCC4
328	help
329	  Various DSCC4 bugs forbid any reliable software reset of the ASIC.
330	  As a replacement, some vendors provide a way to assert the PCI #RST
331	  pin of DSCC4 through the GPIO port of the card. If you choose Y,
332	  the driver will make use of this feature before module removal
333	  (i.e. rmmod). The feature is known to be available on Commtech's
334	  cards. Contact your manufacturer for details.
336	  Say Y if your card supports this feature.
338config IXP4XX_HSS
339	tristate "Intel IXP4xx HSS (synchronous serial port) support"
340	depends on HDLC && ARM && ARCH_IXP4XX && IXP4XX_NPE && IXP4XX_QMGR
341	help
342	  Say Y here if you want to use built-in HSS ports
343	  on IXP4xx processor.
345config DLCI
346	tristate "Frame Relay DLCI support"
347	---help---
348	  Support for the Frame Relay protocol.
350	  Frame Relay is a fast low-cost way to connect to a remote Internet
351	  access provider or to form a private wide area network. The one
352	  physical line from your box to the local "switch" (i.e. the entry
353	  point to the Frame Relay network, usually at the phone company) can
354	  carry several logical point-to-point connections to other computers
355	  connected to the Frame Relay network. For a general explanation of
356	  the protocol, check out <>.
358	  To use frame relay, you need supporting hardware (called FRAD) and
359	  certain programs from the net-tools package as explained in
360	  <file:Documentation/networking/framerelay.txt>.
362	  To compile this driver as a module, choose M here: the
363	  module will be called dlci.
365config DLCI_MAX
366	int "Max DLCI per device"
367	depends on DLCI
368	default "8"
369	help
370	  How many logical point-to-point frame relay connections (the
371	  identifiers of which are called DCLIs) should be handled by each
372	  of your hardware frame relay access devices.
374	  Go with the default.
376config SDLA
377	tristate "SDLA (Sangoma S502/S508) support"
378	depends on DLCI && ISA
379	help
380	  Driver for the Sangoma S502A, S502E, and S508 Frame Relay Access
381	  Devices.
383	  These are multi-protocol cards, but only Frame Relay is supported
384	  by the driver at this time. Please read
385	  <file:Documentation/networking/framerelay.txt>.
387	  To compile this driver as a module, choose M here: the
388	  module will be called sdla.
390# Wan router core.
392	tristate "WAN router drivers"
393	depends on WAN_ROUTER
394	---help---
395	  Connect LAN to WAN via Linux box.
397	  Select driver your card and remember to say Y to "Wan Router."
398	  You will need the wan-tools package which is available from
399	  <>.
401	  Note that the answer to this question won't directly affect the
402	  kernel except for how subordinate drivers may be built:
403	  saying N will just cause the configurator to skip all
404	  the questions about WAN router drivers.
406	  If unsure, say N.
409	tristate "Cyclom 2X(tm) cards (EXPERIMENTAL)"
410	depends on WAN_ROUTER_DRIVERS && (PCI || ISA)
411	---help---
412	  Cyclom 2X from Cyclades Corporation <> is an
413	  intelligent multiprotocol WAN adapter with data transfer rates up to
414	  512 Kbps. These cards support the X.25 and SNA related protocols.
416	  While no documentation is available at this time please grab the
417	  wanconfig tarball in
418	  <> (with minor changes
419	  to make it compile with the current wanrouter include files; efforts
420	  are being made to use the original package available at
421	  <>).
423	  Feel free to contact me or the cycsyn-devel mailing list at
424	  <> and <> for
425	  additional details, I hope to have documentation available as soon as
426	  possible. (Cyclades Brazil is writing the Documentation).
428	  The next questions will ask you about the protocols you want the
429	  driver to support (for now only X.25 is supported).
431	  If you have one or more of these cards, say Y to this option.
433	  To compile this driver as a module, choose M here: the
434	  module will be called cyclomx.
436config CYCLOMX_X25
437	bool "Cyclom 2X X.25 support (EXPERIMENTAL)"
438	depends on CYCLADES_SYNC
439	help
440	  Connect a Cyclom 2X card to an X.25 network.
442	  Enabling X.25 support will enlarge your kernel by about 11 kB.
444# X.25 network drivers
445config LAPBETHER
446	tristate "LAPB over Ethernet driver (EXPERIMENTAL)"
447	depends on LAPB && X25
448	---help---
449	  Driver for a pseudo device (typically called /dev/lapb0) which allows
450	  you to open an LAPB point-to-point connection to some other computer
451	  on your Ethernet network.
453	  In order to do this, you need to say Y or M to the driver for your
454	  Ethernet card as well as to "LAPB Data Link Driver".
456	  To compile this driver as a module, choose M here: the
457	  module will be called lapbether.
459	  If unsure, say N.
461config X25_ASY
462	tristate "X.25 async driver (EXPERIMENTAL)"
463	depends on LAPB && X25
464	---help---
465	  Send and receive X.25 frames over regular asynchronous serial
466	  lines such as telephone lines equipped with ordinary modems.
468	  Experts should note that this driver doesn't currently comply with
469	  the asynchronous HDLS framing protocols in CCITT recommendation X.25.
471	  To compile this driver as a module, choose M here: the
472	  module will be called x25_asy.
474	  If unsure, say N.
476config SBNI
477	tristate "Granch SBNI12 Leased Line adapter support"
478	depends on X86
479	---help---
480	  Driver for ISA SBNI12-xx cards which are low cost alternatives to
481	  leased line modems.
483	  You can find more information and last versions of drivers and
484	  utilities at <>. If you have any question you
485	  can send email to <>.
487	  To compile this driver as a module, choose M here: the
488	  module will be called sbni.
490	  If unsure, say N.
493	bool "Multiple line feature support"
494	depends on SBNI
495	help
496	  Schedule traffic for some parallel lines, via SBNI12 adapters.
498	  If you have two computers connected with two parallel lines it's
499	  possible to increase transfer rate nearly twice. You should have
500	  a program named 'sbniconfig' to configure adapters.
502	  If unsure, say N.
504endif # WAN