/drivers/e1000-4.x/src/e1000_hw.c
C | 3590 lines | 2086 code | 367 blank | 1137 comment | 376 complexity | c2a0dd98e1f79d544cf2989f097ca85c MD5 | raw file
Possible License(s): GPL-2.0, BSD-3-Clause
Large files files are truncated, but you can click here to view the full file
- /*******************************************************************************
-
- Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.
-
- This program is free software; you can redistribute it and/or modify it
- under the terms of the GNU General Public License as published by the Free
- Software Foundation; either version 2 of the License, or (at your option)
- any later version.
-
- This program is distributed in the hope that it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- more details.
-
- You should have received a copy of the GNU General Public License along with
- this program; if not, write to the Free Software Foundation, Inc., 59
- Temple Place - Suite 330, Boston, MA 02111-1307, USA.
-
- The full GNU General Public License is included in this distribution in the
- file called LICENSE.
-
- Contact Information:
- Linux NICS <linux.nics@intel.com>
- Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
- *******************************************************************************/
- /* e1000_hw.c
- * Shared functions for accessing and configuring the MAC
- */
- #include "e1000_hw.h"
- static int32_t e1000_setup_fiber_link(struct e1000_hw *hw);
- static int32_t e1000_setup_copper_link(struct e1000_hw *hw);
- static int32_t e1000_phy_force_speed_duplex(struct e1000_hw *hw);
- static int32_t e1000_config_mac_to_phy(struct e1000_hw *hw);
- static int32_t e1000_force_mac_fc(struct e1000_hw *hw);
- static void e1000_raise_mdi_clk(struct e1000_hw *hw, uint32_t *ctrl);
- static void e1000_lower_mdi_clk(struct e1000_hw *hw, uint32_t *ctrl);
- static void e1000_shift_out_mdi_bits(struct e1000_hw *hw, uint32_t data, uint16_t count);
- static uint16_t e1000_shift_in_mdi_bits(struct e1000_hw *hw);
- static int32_t e1000_phy_reset_dsp(struct e1000_hw *hw);
- static void e1000_raise_ee_clk(struct e1000_hw *hw, uint32_t *eecd);
- static void e1000_lower_ee_clk(struct e1000_hw *hw, uint32_t *eecd);
- static void e1000_shift_out_ee_bits(struct e1000_hw *hw, uint16_t data, uint16_t count);
- static uint16_t e1000_shift_in_ee_bits(struct e1000_hw *hw);
- static void e1000_setup_eeprom(struct e1000_hw *hw);
- static void e1000_standby_eeprom(struct e1000_hw *hw);
- static void e1000_clock_eeprom(struct e1000_hw *hw);
- static void e1000_cleanup_eeprom(struct e1000_hw *hw);
- static int32_t e1000_id_led_init(struct e1000_hw * hw);
- /******************************************************************************
- * Set the mac type member in the hw struct.
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
- int32_t
- e1000_set_mac_type(struct e1000_hw *hw)
- {
- DEBUGFUNC("e1000_set_mac_type");
- switch (hw->device_id) {
- case E1000_DEV_ID_82542:
- switch (hw->revision_id) {
- case E1000_82542_2_0_REV_ID:
- hw->mac_type = e1000_82542_rev2_0;
- break;
- case E1000_82542_2_1_REV_ID:
- hw->mac_type = e1000_82542_rev2_1;
- break;
- default:
- /* Invalid 82542 revision ID */
- return -E1000_ERR_MAC_TYPE;
- }
- break;
- case E1000_DEV_ID_82543GC_FIBER:
- case E1000_DEV_ID_82543GC_COPPER:
- hw->mac_type = e1000_82543;
- break;
- case E1000_DEV_ID_82544EI_COPPER:
- case E1000_DEV_ID_82544EI_FIBER:
- case E1000_DEV_ID_82544GC_COPPER:
- case E1000_DEV_ID_82544GC_LOM:
- hw->mac_type = e1000_82544;
- break;
- case E1000_DEV_ID_82540EM:
- case E1000_DEV_ID_82540EM_LOM:
- hw->mac_type = e1000_82540;
- break;
- case E1000_DEV_ID_82545EM_COPPER:
- case E1000_DEV_ID_82545EM_FIBER:
- hw->mac_type = e1000_82545;
- break;
- case E1000_DEV_ID_82546EB_COPPER:
- case E1000_DEV_ID_82546EB_FIBER:
- hw->mac_type = e1000_82546;
- break;
- default:
- /* Should never have loaded on this device */
- return -E1000_ERR_MAC_TYPE;
- }
- return E1000_SUCCESS;
- }
- /******************************************************************************
- * Reset the transmit and receive units; mask and clear all interrupts.
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
- void
- e1000_reset_hw(struct e1000_hw *hw)
- {
- uint32_t ctrl;
- uint32_t ctrl_ext;
- uint32_t icr;
- uint32_t manc;
- DEBUGFUNC("e1000_reset_hw");
-
- /* For 82542 (rev 2.0), disable MWI before issuing a device reset */
- if(hw->mac_type == e1000_82542_rev2_0) {
- DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
- e1000_pci_clear_mwi(hw);
- }
- /* Clear interrupt mask to stop board from generating interrupts */
- DEBUGOUT("Masking off all interrupts\n");
- E1000_WRITE_REG(hw, IMC, 0xffffffff);
- /* Disable the Transmit and Receive units. Then delay to allow
- * any pending transactions to complete before we hit the MAC with
- * the global reset.
- */
- E1000_WRITE_REG(hw, RCTL, 0);
- E1000_WRITE_REG(hw, TCTL, E1000_TCTL_PSP);
- E1000_WRITE_FLUSH(hw);
- /* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */
- hw->tbi_compatibility_on = FALSE;
- /* Delay to allow any outstanding PCI transactions to complete before
- * resetting the device
- */
- msec_delay(10);
- /* Issue a global reset to the MAC. This will reset the chip's
- * transmit, receive, DMA, and link units. It will not effect
- * the current PCI configuration. The global reset bit is self-
- * clearing, and should clear within a microsecond.
- */
- DEBUGOUT("Issuing a global reset to MAC\n");
- ctrl = E1000_READ_REG(hw, CTRL);
- if(hw->mac_type > e1000_82543)
- E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_RST));
- else
- E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST));
- /* Force a reload from the EEPROM if necessary */
- if(hw->mac_type < e1000_82540) {
- /* Wait for reset to complete */
- usec_delay(10);
- ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
- ctrl_ext |= E1000_CTRL_EXT_EE_RST;
- E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
- E1000_WRITE_FLUSH(hw);
- /* Wait for EEPROM reload */
- msec_delay(2);
- } else {
- /* Wait for EEPROM reload (it happens automatically) */
- msec_delay(4);
- /* Dissable HW ARPs on ASF enabled adapters */
- manc = E1000_READ_REG(hw, MANC);
- manc &= ~(E1000_MANC_ARP_EN);
- E1000_WRITE_REG(hw, MANC, manc);
- }
-
- /* Clear interrupt mask to stop board from generating interrupts */
- DEBUGOUT("Masking off all interrupts\n");
- E1000_WRITE_REG(hw, IMC, 0xffffffff);
- /* Clear any pending interrupt events. */
- icr = E1000_READ_REG(hw, ICR);
- /* If MWI was previously enabled, reenable it. */
- if(hw->mac_type == e1000_82542_rev2_0) {
- if(hw->pci_cmd_word & CMD_MEM_WRT_INVALIDATE)
- e1000_pci_set_mwi(hw);
- }
- }
- /******************************************************************************
- * Performs basic configuration of the adapter.
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Assumes that the controller has previously been reset and is in a
- * post-reset uninitialized state. Initializes the receive address registers,
- * multicast table, and VLAN filter table. Calls routines to setup link
- * configuration and flow control settings. Clears all on-chip counters. Leaves
- * the transmit and receive units disabled and uninitialized.
- *****************************************************************************/
- int32_t
- e1000_init_hw(struct e1000_hw *hw)
- {
- uint32_t ctrl, status;
- uint32_t i;
- int32_t ret_val;
- uint16_t pcix_cmd_word;
- uint16_t pcix_stat_hi_word;
- uint16_t cmd_mmrbc;
- uint16_t stat_mmrbc;
- DEBUGFUNC("e1000_init_hw");
- /* Initialize Identification LED */
- ret_val = e1000_id_led_init(hw);
- if(ret_val < 0) {
- DEBUGOUT("Error Initializing Identification LED\n");
- return ret_val;
- }
-
- /* Set the Media Type and exit with error if it is not valid. */
- if(hw->mac_type != e1000_82543) {
- /* tbi_compatibility is only valid on 82543 */
- hw->tbi_compatibility_en = FALSE;
- }
- if(hw->mac_type >= e1000_82543) {
- status = E1000_READ_REG(hw, STATUS);
- if(status & E1000_STATUS_TBIMODE) {
- hw->media_type = e1000_media_type_fiber;
- /* tbi_compatibility not valid on fiber */
- hw->tbi_compatibility_en = FALSE;
- } else {
- hw->media_type = e1000_media_type_copper;
- }
- } else {
- /* This is an 82542 (fiber only) */
- hw->media_type = e1000_media_type_fiber;
- }
- /* Disabling VLAN filtering. */
- DEBUGOUT("Initializing the IEEE VLAN\n");
- E1000_WRITE_REG(hw, VET, 0);
- e1000_clear_vfta(hw);
- /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
- if(hw->mac_type == e1000_82542_rev2_0) {
- DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
- e1000_pci_clear_mwi(hw);
- E1000_WRITE_REG(hw, RCTL, E1000_RCTL_RST);
- E1000_WRITE_FLUSH(hw);
- msec_delay(5);
- }
- /* Setup the receive address. This involves initializing all of the Receive
- * Address Registers (RARs 0 - 15).
- */
- e1000_init_rx_addrs(hw);
- /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */
- if(hw->mac_type == e1000_82542_rev2_0) {
- E1000_WRITE_REG(hw, RCTL, 0);
- E1000_WRITE_FLUSH(hw);
- msec_delay(1);
- if(hw->pci_cmd_word & CMD_MEM_WRT_INVALIDATE)
- e1000_pci_set_mwi(hw);
- }
- /* Zero out the Multicast HASH table */
- DEBUGOUT("Zeroing the MTA\n");
- for(i = 0; i < E1000_MC_TBL_SIZE; i++)
- E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
- /* Set the PCI priority bit correctly in the CTRL register. This
- * determines if the adapter gives priority to receives, or if it
- * gives equal priority to transmits and receives.
- */
- if(hw->dma_fairness) {
- ctrl = E1000_READ_REG(hw, CTRL);
- E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PRIOR);
- }
- /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */
- if(hw->bus_type == e1000_bus_type_pcix) {
- e1000_read_pci_cfg(hw, PCIX_COMMAND_REGISTER, &pcix_cmd_word);
- e1000_read_pci_cfg(hw, PCIX_STATUS_REGISTER_HI, &pcix_stat_hi_word);
- cmd_mmrbc = (pcix_cmd_word & PCIX_COMMAND_MMRBC_MASK) >>
- PCIX_COMMAND_MMRBC_SHIFT;
- stat_mmrbc = (pcix_stat_hi_word & PCIX_STATUS_HI_MMRBC_MASK) >>
- PCIX_STATUS_HI_MMRBC_SHIFT;
- if(stat_mmrbc == PCIX_STATUS_HI_MMRBC_4K)
- stat_mmrbc = PCIX_STATUS_HI_MMRBC_2K;
- if(cmd_mmrbc > stat_mmrbc) {
- pcix_cmd_word &= ~PCIX_COMMAND_MMRBC_MASK;
- pcix_cmd_word |= stat_mmrbc << PCIX_COMMAND_MMRBC_SHIFT;
- e1000_write_pci_cfg(hw, PCIX_COMMAND_REGISTER, &pcix_cmd_word);
- }
- }
- /* Call a subroutine to configure the link and setup flow control. */
- ret_val = e1000_setup_link(hw);
- /* Set the transmit descriptor write-back policy */
- if(hw->mac_type > e1000_82544) {
- ctrl = E1000_READ_REG(hw, TXDCTL);
- ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB;
- E1000_WRITE_REG(hw, TXDCTL, ctrl);
- }
- /* Clear all of the statistics registers (clear on read). It is
- * important that we do this after we have tried to establish link
- * because the symbol error count will increment wildly if there
- * is no link.
- */
- e1000_clear_hw_cntrs(hw);
- return ret_val;
- }
- /******************************************************************************
- * Configures flow control and link settings.
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Determines which flow control settings to use. Calls the apropriate media-
- * specific link configuration function. Configures the flow control settings.
- * Assuming the adapter has a valid link partner, a valid link should be
- * established. Assumes the hardware has previously been reset and the
- * transmitter and receiver are not enabled.
- *****************************************************************************/
- int32_t
- e1000_setup_link(struct e1000_hw *hw)
- {
- uint32_t ctrl_ext;
- int32_t ret_val;
- uint16_t eeprom_data;
- DEBUGFUNC("e1000_setup_link");
- /* Read and store word 0x0F of the EEPROM. This word contains bits
- * that determine the hardware's default PAUSE (flow control) mode,
- * a bit that determines whether the HW defaults to enabling or
- * disabling auto-negotiation, and the direction of the
- * SW defined pins. If there is no SW over-ride of the flow
- * control setting, then the variable hw->fc will
- * be initialized based on a value in the EEPROM.
- */
- if(e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, &eeprom_data) < 0) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
- if(hw->fc == e1000_fc_default) {
- if((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
- hw->fc = e1000_fc_none;
- else if((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
- EEPROM_WORD0F_ASM_DIR)
- hw->fc = e1000_fc_tx_pause;
- else
- hw->fc = e1000_fc_full;
- }
- /* We want to save off the original Flow Control configuration just
- * in case we get disconnected and then reconnected into a different
- * hub or switch with different Flow Control capabilities.
- */
- if(hw->mac_type == e1000_82542_rev2_0)
- hw->fc &= (~e1000_fc_tx_pause);
- if((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1))
- hw->fc &= (~e1000_fc_rx_pause);
- hw->original_fc = hw->fc;
- DEBUGOUT1("After fix-ups FlowControl is now = %x\n", hw->fc);
- /* Take the 4 bits from EEPROM word 0x0F that determine the initial
- * polarity value for the SW controlled pins, and setup the
- * Extended Device Control reg with that info.
- * This is needed because one of the SW controlled pins is used for
- * signal detection. So this should be done before e1000_setup_pcs_link()
- * or e1000_phy_setup() is called.
- */
- if(hw->mac_type == e1000_82543) {
- ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) <<
- SWDPIO__EXT_SHIFT);
- E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
- }
- /* Call the necessary subroutine to configure the link. */
- ret_val = (hw->media_type == e1000_media_type_fiber) ?
- e1000_setup_fiber_link(hw) :
- e1000_setup_copper_link(hw);
- /* Initialize the flow control address, type, and PAUSE timer
- * registers to their default values. This is done even if flow
- * control is disabled, because it does not hurt anything to
- * initialize these registers.
- */
- DEBUGOUT("Initializing the Flow Control address, type and timer regs\n");
- E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW);
- E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH);
- E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE);
- E1000_WRITE_REG(hw, FCTTV, hw->fc_pause_time);
- /* Set the flow control receive threshold registers. Normally,
- * these registers will be set to a default threshold that may be
- * adjusted later by the driver's runtime code. However, if the
- * ability to transmit pause frames in not enabled, then these
- * registers will be set to 0.
- */
- if(!(hw->fc & e1000_fc_tx_pause)) {
- E1000_WRITE_REG(hw, FCRTL, 0);
- E1000_WRITE_REG(hw, FCRTH, 0);
- } else {
- /* We need to set up the Receive Threshold high and low water marks
- * as well as (optionally) enabling the transmission of XON frames.
- */
- if(hw->fc_send_xon) {
- E1000_WRITE_REG(hw, FCRTL, (hw->fc_low_water | E1000_FCRTL_XONE));
- E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water);
- } else {
- E1000_WRITE_REG(hw, FCRTL, hw->fc_low_water);
- E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water);
- }
- }
- return ret_val;
- }
- /******************************************************************************
- * Sets up link for a fiber based adapter
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Manipulates Physical Coding Sublayer functions in order to configure
- * link. Assumes the hardware has been previously reset and the transmitter
- * and receiver are not enabled.
- *****************************************************************************/
- static int32_t
- e1000_setup_fiber_link(struct e1000_hw *hw)
- {
- uint32_t ctrl;
- uint32_t status;
- uint32_t txcw = 0;
- uint32_t i;
- uint32_t signal;
- int32_t ret_val;
- DEBUGFUNC("e1000_setup_fiber_link");
- /* On adapters with a MAC newer that 82544, SW Defineable pin 1 will be
- * set when the optics detect a signal. On older adapters, it will be
- * cleared when there is a signal
- */
- ctrl = E1000_READ_REG(hw, CTRL);
- if(hw->mac_type > e1000_82544) signal = E1000_CTRL_SWDPIN1;
- else signal = 0;
-
- /* Take the link out of reset */
- ctrl &= ~(E1000_CTRL_LRST);
-
- e1000_config_collision_dist(hw);
- /* Check for a software override of the flow control settings, and setup
- * the device accordingly. If auto-negotiation is enabled, then software
- * will have to set the "PAUSE" bits to the correct value in the Tranmsit
- * Config Word Register (TXCW) and re-start auto-negotiation. However, if
- * auto-negotiation is disabled, then software will have to manually
- * configure the two flow control enable bits in the CTRL register.
- *
- * The possible values of the "fc" parameter are:
- * 0: Flow control is completely disabled
- * 1: Rx flow control is enabled (we can receive pause frames, but
- * not send pause frames).
- * 2: Tx flow control is enabled (we can send pause frames but we do
- * not support receiving pause frames).
- * 3: Both Rx and TX flow control (symmetric) are enabled.
- */
- switch (hw->fc) {
- case e1000_fc_none:
- /* Flow control is completely disabled by a software over-ride. */
- txcw = (E1000_TXCW_ANE | E1000_TXCW_FD);
- break;
- case e1000_fc_rx_pause:
- /* RX Flow control is enabled and TX Flow control is disabled by a
- * software over-ride. Since there really isn't a way to advertise
- * that we are capable of RX Pause ONLY, we will advertise that we
- * support both symmetric and asymmetric RX PAUSE. Later, we will
- * disable the adapter's ability to send PAUSE frames.
- */
- txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
- break;
- case e1000_fc_tx_pause:
- /* TX Flow control is enabled, and RX Flow control is disabled, by a
- * software over-ride.
- */
- txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR);
- break;
- case e1000_fc_full:
- /* Flow control (both RX and TX) is enabled by a software over-ride. */
- txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
- break;
- default:
- DEBUGOUT("Flow control param set incorrectly\n");
- return -E1000_ERR_CONFIG;
- break;
- }
- /* Since auto-negotiation is enabled, take the link out of reset (the link
- * will be in reset, because we previously reset the chip). This will
- * restart auto-negotiation. If auto-neogtiation is successful then the
- * link-up status bit will be set and the flow control enable bits (RFCE
- * and TFCE) will be set according to their negotiated value.
- */
- DEBUGOUT("Auto-negotiation enabled\n");
- E1000_WRITE_REG(hw, TXCW, txcw);
- E1000_WRITE_REG(hw, CTRL, ctrl);
- E1000_WRITE_FLUSH(hw);
- hw->txcw = txcw;
- msec_delay(1);
- /* If we have a signal (the cable is plugged in) then poll for a "Link-Up"
- * indication in the Device Status Register. Time-out if a link isn't
- * seen in 500 milliseconds seconds (Auto-negotiation should complete in
- * less than 500 milliseconds even if the other end is doing it in SW).
- */
- if((E1000_READ_REG(hw, CTRL) & E1000_CTRL_SWDPIN1) == signal) {
- DEBUGOUT("Looking for Link\n");
- for(i = 0; i < (LINK_UP_TIMEOUT / 10); i++) {
- msec_delay(10);
- status = E1000_READ_REG(hw, STATUS);
- if(status & E1000_STATUS_LU) break;
- }
- if(i == (LINK_UP_TIMEOUT / 10)) {
- /* AutoNeg failed to achieve a link, so we'll call
- * e1000_check_for_link. This routine will force the link up if we
- * detect a signal. This will allow us to communicate with
- * non-autonegotiating link partners.
- */
- DEBUGOUT("Never got a valid link from auto-neg!!!\n");
- hw->autoneg_failed = 1;
- ret_val = e1000_check_for_link(hw);
- if(ret_val < 0) {
- DEBUGOUT("Error while checking for link\n");
- return ret_val;
- }
- hw->autoneg_failed = 0;
- } else {
- hw->autoneg_failed = 0;
- DEBUGOUT("Valid Link Found\n");
- }
- } else {
- DEBUGOUT("No Signal Detected\n");
- }
- return 0;
- }
- /******************************************************************************
- * Detects which PHY is present and the speed and duplex
- *
- * hw - Struct containing variables accessed by shared code
- ******************************************************************************/
- static int32_t
- e1000_setup_copper_link(struct e1000_hw *hw)
- {
- uint32_t ctrl;
- int32_t ret_val;
- uint16_t i;
- uint16_t phy_data;
- DEBUGFUNC("e1000_setup_copper_link");
- ctrl = E1000_READ_REG(hw, CTRL);
- /* With 82543, we need to force speed and duplex on the MAC equal to what
- * the PHY speed and duplex configuration is. In addition, we need to
- * perform a hardware reset on the PHY to take it out of reset.
- */
- if(hw->mac_type > e1000_82543) {
- ctrl |= E1000_CTRL_SLU;
- ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
- E1000_WRITE_REG(hw, CTRL, ctrl);
- } else {
- ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX | E1000_CTRL_SLU);
- E1000_WRITE_REG(hw, CTRL, ctrl);
- e1000_phy_hw_reset(hw);
- }
- /* Make sure we have a valid PHY */
- ret_val = e1000_detect_gig_phy(hw);
- if(ret_val < 0) {
- DEBUGOUT("Error, did not detect valid phy.\n");
- return ret_val;
- }
- DEBUGOUT1("Phy ID = %x \n", hw->phy_id);
- /* Enable CRS on TX. This must be set for half-duplex operation. */
- if(e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
- /* Options:
- * MDI/MDI-X = 0 (default)
- * 0 - Auto for all speeds
- * 1 - MDI mode
- * 2 - MDI-X mode
- * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
- */
- phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
- switch (hw->mdix) {
- case 1:
- phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
- break;
- case 2:
- phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
- break;
- case 3:
- phy_data |= M88E1000_PSCR_AUTO_X_1000T;
- break;
- case 0:
- default:
- phy_data |= M88E1000_PSCR_AUTO_X_MODE;
- break;
- }
- /* Options:
- * disable_polarity_correction = 0 (default)
- * Automatic Correction for Reversed Cable Polarity
- * 0 - Disabled
- * 1 - Enabled
- */
- phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
- if(hw->disable_polarity_correction == 1)
- phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
- if(e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data) < 0) {
- DEBUGOUT("PHY Write Error\n");
- return -E1000_ERR_PHY;
- }
- /* Force TX_CLK in the Extended PHY Specific Control Register
- * to 25MHz clock.
- */
- if(e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- phy_data |= M88E1000_EPSCR_TX_CLK_25;
- /* Configure Master and Slave downshift values */
- phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK |
- M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
- phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X |
- M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
- if(e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data) < 0) {
- DEBUGOUT("PHY Write Error\n");
- return -E1000_ERR_PHY;
- }
- /* SW Reset the PHY so all changes take effect */
- ret_val = e1000_phy_reset(hw);
- if(ret_val < 0) {
- DEBUGOUT("Error Resetting the PHY\n");
- return ret_val;
- }
-
- /* Options:
- * autoneg = 1 (default)
- * PHY will advertise value(s) parsed from
- * autoneg_advertised and fc
- * autoneg = 0
- * PHY will be set to 10H, 10F, 100H, or 100F
- * depending on value parsed from forced_speed_duplex.
- */
- /* Is autoneg enabled? This is enabled by default or by software override.
- * If so, call e1000_phy_setup_autoneg routine to parse the
- * autoneg_advertised and fc options. If autoneg is NOT enabled, then the
- * user should have provided a speed/duplex override. If so, then call
- * e1000_phy_force_speed_duplex to parse and set this up.
- */
- if(hw->autoneg) {
- /* Perform some bounds checking on the hw->autoneg_advertised
- * parameter. If this variable is zero, then set it to the default.
- */
- hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT;
- /* If autoneg_advertised is zero, we assume it was not defaulted
- * by the calling code so we set to advertise full capability.
- */
- if(hw->autoneg_advertised == 0)
- hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
- DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
- ret_val = e1000_phy_setup_autoneg(hw);
- if(ret_val < 0) {
- DEBUGOUT("Error Setting up Auto-Negotiation\n");
- return ret_val;
- }
- DEBUGOUT("Restarting Auto-Neg\n");
- /* Restart auto-negotiation by setting the Auto Neg Enable bit and
- * the Auto Neg Restart bit in the PHY control register.
- */
- if(e1000_read_phy_reg(hw, PHY_CTRL, &phy_data) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
- if(e1000_write_phy_reg(hw, PHY_CTRL, phy_data) < 0) {
- DEBUGOUT("PHY Write Error\n");
- return -E1000_ERR_PHY;
- }
- /* Does the user want to wait for Auto-Neg to complete here, or
- * check at a later time (for example, callback routine).
- */
- if(hw->wait_autoneg_complete) {
- ret_val = e1000_wait_autoneg(hw);
- if(ret_val < 0) {
- DEBUGOUT("Error while waiting for autoneg to complete\n");
- return ret_val;
- }
- }
- } else {
- DEBUGOUT("Forcing speed and duplex\n");
- ret_val = e1000_phy_force_speed_duplex(hw);
- if(ret_val < 0) {
- DEBUGOUT("Error Forcing Speed and Duplex\n");
- return ret_val;
- }
- }
- /* Check link status. Wait up to 100 microseconds for link to become
- * valid.
- */
- for(i = 0; i < 10; i++) {
- if(e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- if(e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- if(phy_data & MII_SR_LINK_STATUS) {
- /* We have link, so we need to finish the config process:
- * 1) Set up the MAC to the current PHY speed/duplex
- * if we are on 82543. If we
- * are on newer silicon, we only need to configure
- * collision distance in the Transmit Control Register.
- * 2) Set up flow control on the MAC to that established with
- * the link partner.
- */
- if(hw->mac_type >= e1000_82544) {
- e1000_config_collision_dist(hw);
- } else {
- ret_val = e1000_config_mac_to_phy(hw);
- if(ret_val < 0) {
- DEBUGOUT("Error configuring MAC to PHY settings\n");
- return ret_val;
- }
- }
- ret_val = e1000_config_fc_after_link_up(hw);
- if(ret_val < 0) {
- DEBUGOUT("Error Configuring Flow Control\n");
- return ret_val;
- }
- DEBUGOUT("Valid link established!!!\n");
- return 0;
- }
- usec_delay(10);
- }
- DEBUGOUT("Unable to establish link!!!\n");
- return 0;
- }
- /******************************************************************************
- * Configures PHY autoneg and flow control advertisement settings
- *
- * hw - Struct containing variables accessed by shared code
- ******************************************************************************/
- int32_t
- e1000_phy_setup_autoneg(struct e1000_hw *hw)
- {
- uint16_t mii_autoneg_adv_reg;
- uint16_t mii_1000t_ctrl_reg;
- DEBUGFUNC("e1000_phy_setup_autoneg");
- /* Read the MII Auto-Neg Advertisement Register (Address 4). */
- if(e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- /* Read the MII 1000Base-T Control Register (Address 9). */
- if(e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- /* Need to parse both autoneg_advertised and fc and set up
- * the appropriate PHY registers. First we will parse for
- * autoneg_advertised software override. Since we can advertise
- * a plethora of combinations, we need to check each bit
- * individually.
- */
- /* First we clear all the 10/100 mb speed bits in the Auto-Neg
- * Advertisement Register (Address 4) and the 1000 mb speed bits in
- * the 1000Base-T Control Register (Address 9).
- */
- mii_autoneg_adv_reg &= ~REG4_SPEED_MASK;
- mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK;
- DEBUGOUT1("autoneg_advertised %x\n", hw->autoneg_advertised);
- /* Do we want to advertise 10 Mb Half Duplex? */
- if(hw->autoneg_advertised & ADVERTISE_10_HALF) {
- DEBUGOUT("Advertise 10mb Half duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
- }
- /* Do we want to advertise 10 Mb Full Duplex? */
- if(hw->autoneg_advertised & ADVERTISE_10_FULL) {
- DEBUGOUT("Advertise 10mb Full duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
- }
- /* Do we want to advertise 100 Mb Half Duplex? */
- if(hw->autoneg_advertised & ADVERTISE_100_HALF) {
- DEBUGOUT("Advertise 100mb Half duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
- }
- /* Do we want to advertise 100 Mb Full Duplex? */
- if(hw->autoneg_advertised & ADVERTISE_100_FULL) {
- DEBUGOUT("Advertise 100mb Full duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
- }
- /* We do not allow the Phy to advertise 1000 Mb Half Duplex */
- if(hw->autoneg_advertised & ADVERTISE_1000_HALF) {
- DEBUGOUT("Advertise 1000mb Half duplex requested, request denied!\n");
- }
- /* Do we want to advertise 1000 Mb Full Duplex? */
- if(hw->autoneg_advertised & ADVERTISE_1000_FULL) {
- DEBUGOUT("Advertise 1000mb Full duplex\n");
- mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
- }
- /* Check for a software override of the flow control settings, and
- * setup the PHY advertisement registers accordingly. If
- * auto-negotiation is enabled, then software will have to set the
- * "PAUSE" bits to the correct value in the Auto-Negotiation
- * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation.
- *
- * The possible values of the "fc" parameter are:
- * 0: Flow control is completely disabled
- * 1: Rx flow control is enabled (we can receive pause frames
- * but not send pause frames).
- * 2: Tx flow control is enabled (we can send pause frames
- * but we do not support receiving pause frames).
- * 3: Both Rx and TX flow control (symmetric) are enabled.
- * other: No software override. The flow control configuration
- * in the EEPROM is used.
- */
- switch (hw->fc) {
- case e1000_fc_none: /* 0 */
- /* Flow control (RX & TX) is completely disabled by a
- * software over-ride.
- */
- mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
- break;
- case e1000_fc_rx_pause: /* 1 */
- /* RX Flow control is enabled, and TX Flow control is
- * disabled, by a software over-ride.
- */
- /* Since there really isn't a way to advertise that we are
- * capable of RX Pause ONLY, we will advertise that we
- * support both symmetric and asymmetric RX PAUSE. Later
- * (in e1000_config_fc_after_link_up) we will disable the
- *hw's ability to send PAUSE frames.
- */
- mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
- break;
- case e1000_fc_tx_pause: /* 2 */
- /* TX Flow control is enabled, and RX Flow control is
- * disabled, by a software over-ride.
- */
- mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
- mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
- break;
- case e1000_fc_full: /* 3 */
- /* Flow control (both RX and TX) is enabled by a software
- * over-ride.
- */
- mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
- break;
- default:
- DEBUGOUT("Flow control param set incorrectly\n");
- return -E1000_ERR_CONFIG;
- }
- if(e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg) < 0) {
- DEBUGOUT("PHY Write Error\n");
- return -E1000_ERR_PHY;
- }
- DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
- if(e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg) < 0) {
- DEBUGOUT("PHY Write Error\n");
- return -E1000_ERR_PHY;
- }
- return 0;
- }
- /******************************************************************************
- * Force PHY speed and duplex settings to hw->forced_speed_duplex
- *
- * hw - Struct containing variables accessed by shared code
- ******************************************************************************/
- static int32_t
- e1000_phy_force_speed_duplex(struct e1000_hw *hw)
- {
- uint32_t ctrl;
- int32_t ret_val;
- uint16_t mii_ctrl_reg;
- uint16_t mii_status_reg;
- uint16_t phy_data;
- uint16_t i;
- DEBUGFUNC("e1000_phy_force_speed_duplex");
- /* Turn off Flow control if we are forcing speed and duplex. */
- hw->fc = e1000_fc_none;
- DEBUGOUT1("hw->fc = %d\n", hw->fc);
- /* Read the Device Control Register. */
- ctrl = E1000_READ_REG(hw, CTRL);
- /* Set the bits to Force Speed and Duplex in the Device Ctrl Reg. */
- ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
- ctrl &= ~(DEVICE_SPEED_MASK);
- /* Clear the Auto Speed Detect Enable bit. */
- ctrl &= ~E1000_CTRL_ASDE;
- /* Read the MII Control Register. */
- if(e1000_read_phy_reg(hw, PHY_CTRL, &mii_ctrl_reg) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- /* We need to disable autoneg in order to force link and duplex. */
- mii_ctrl_reg &= ~MII_CR_AUTO_NEG_EN;
- /* Are we forcing Full or Half Duplex? */
- if(hw->forced_speed_duplex == e1000_100_full ||
- hw->forced_speed_duplex == e1000_10_full) {
- /* We want to force full duplex so we SET the full duplex bits in the
- * Device and MII Control Registers.
- */
- ctrl |= E1000_CTRL_FD;
- mii_ctrl_reg |= MII_CR_FULL_DUPLEX;
- DEBUGOUT("Full Duplex\n");
- } else {
- /* We want to force half duplex so we CLEAR the full duplex bits in
- * the Device and MII Control Registers.
- */
- ctrl &= ~E1000_CTRL_FD;
- mii_ctrl_reg &= ~MII_CR_FULL_DUPLEX;
- DEBUGOUT("Half Duplex\n");
- }
- /* Are we forcing 100Mbps??? */
- if(hw->forced_speed_duplex == e1000_100_full ||
- hw->forced_speed_duplex == e1000_100_half) {
- /* Set the 100Mb bit and turn off the 1000Mb and 10Mb bits. */
- ctrl |= E1000_CTRL_SPD_100;
- mii_ctrl_reg |= MII_CR_SPEED_100;
- mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10);
- DEBUGOUT("Forcing 100mb ");
- } else {
- /* Set the 10Mb bit and turn off the 1000Mb and 100Mb bits. */
- ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
- mii_ctrl_reg |= MII_CR_SPEED_10;
- mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100);
- DEBUGOUT("Forcing 10mb ");
- }
- e1000_config_collision_dist(hw);
- /* Write the configured values back to the Device Control Reg. */
- E1000_WRITE_REG(hw, CTRL, ctrl);
- /* Write the MII Control Register with the new PHY configuration. */
- if(e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
- * forced whenever speed are duplex are forced.
- */
- phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
- if(e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data) < 0) {
- DEBUGOUT("PHY Write Error\n");
- return -E1000_ERR_PHY;
- }
- DEBUGOUT1("M88E1000 PSCR: %x \n", phy_data);
-
- /* Need to reset the PHY or these changes will be ignored */
- mii_ctrl_reg |= MII_CR_RESET;
- if(e1000_write_phy_reg(hw, PHY_CTRL, mii_ctrl_reg) < 0) {
- DEBUGOUT("PHY Write Error\n");
- return -E1000_ERR_PHY;
- }
- usec_delay(1);
- /* The wait_autoneg_complete flag may be a little misleading here.
- * Since we are forcing speed and duplex, Auto-Neg is not enabled.
- * But we do want to delay for a period while forcing only so we
- * don't generate false No Link messages. So we will wait here
- * only if the user has set wait_autoneg_complete to 1, which is
- * the default.
- */
- if(hw->wait_autoneg_complete) {
- /* We will wait for autoneg to complete. */
- DEBUGOUT("Waiting for forced speed/duplex link.\n");
- mii_status_reg = 0;
- /* We will wait for autoneg to complete or 4.5 seconds to expire. */
- for(i = PHY_FORCE_TIME; i > 0; i--) {
- /* Read the MII Status Register and wait for Auto-Neg Complete bit
- * to be set.
- */
- if(e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- if(e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- if(mii_status_reg & MII_SR_LINK_STATUS) break;
- msec_delay(100);
- }
- if(i == 0) { /* We didn't get link */
- /* Reset the DSP and wait again for link. */
-
- ret_val = e1000_phy_reset_dsp(hw);
- if(ret_val < 0) {
- DEBUGOUT("Error Resetting PHY DSP\n");
- return ret_val;
- }
- }
- /* This loop will early-out if the link condition has been met. */
- for(i = PHY_FORCE_TIME; i > 0; i--) {
- if(mii_status_reg & MII_SR_LINK_STATUS) break;
- msec_delay(100);
- /* Read the MII Status Register and wait for Auto-Neg Complete bit
- * to be set.
- */
- if(e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- if(e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- }
- }
-
- /* Because we reset the PHY above, we need to re-force TX_CLK in the
- * Extended PHY Specific Control Register to 25MHz clock. This value
- * defaults back to a 2.5MHz clock when the PHY is reset.
- */
- if(e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- phy_data |= M88E1000_EPSCR_TX_CLK_25;
- if(e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data) < 0) {
- DEBUGOUT("PHY Write Error\n");
- return -E1000_ERR_PHY;
- }
- /* In addition, because of the s/w reset above, we need to enable CRS on
- * TX. This must be set for both full and half duplex operation.
- */
- if(e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
- if(e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data) < 0) {
- DEBUGOUT("PHY Write Error\n");
- return -E1000_ERR_PHY;
- }
- return 0;
- }
- /******************************************************************************
- * Sets the collision distance in the Transmit Control register
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Link should have been established previously. Reads the speed and duplex
- * information from the Device Status register.
- ******************************************************************************/
- void
- e1000_config_collision_dist(struct e1000_hw *hw)
- {
- uint32_t tctl;
- tctl = E1000_READ_REG(hw, TCTL);
- tctl &= ~E1000_TCTL_COLD;
- tctl |= E1000_COLLISION_DISTANCE << E1000_COLD_SHIFT;
- E1000_WRITE_REG(hw, TCTL, tctl);
- E1000_WRITE_FLUSH(hw);
- }
- /******************************************************************************
- * Sets MAC speed and duplex settings to reflect the those in the PHY
- *
- * hw - Struct containing variables accessed by shared code
- * mii_reg - data to write to the MII control register
- *
- * The contents of the PHY register containing the needed information need to
- * be passed in.
- ******************************************************************************/
- static int32_t
- e1000_config_mac_to_phy(struct e1000_hw *hw)
- {
- uint32_t ctrl;
- uint16_t phy_data;
- DEBUGFUNC("e1000_config_mac_to_phy");
- /* Read the Device Control Register and set the bits to Force Speed
- * and Duplex.
- */
- ctrl = E1000_READ_REG(hw, CTRL);
- ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
- ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS);
- /* Set up duplex in the Device Control and Transmit Control
- * registers depending on negotiated values.
- */
- if(e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- if(phy_data & M88E1000_PSSR_DPLX) ctrl |= E1000_CTRL_FD;
- else ctrl &= ~E1000_CTRL_FD;
- e1000_config_collision_dist(hw);
- /* Set up speed in the Device Control register depending on
- * negotiated values.
- */
- if((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
- ctrl |= E1000_CTRL_SPD_1000;
- else if((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS)
- ctrl |= E1000_CTRL_SPD_100;
- /* Write the configured values back to the Device Control Reg. */
- E1000_WRITE_REG(hw, CTRL, ctrl);
- return 0;
- }
- /******************************************************************************
- * Forces the MAC's flow control settings.
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Sets the TFCE and RFCE bits in the device control register to reflect
- * the adapter settings. TFCE and RFCE need to be explicitly set by
- * software when a Copper PHY is used because autonegotiation is managed
- * by the PHY rather than the MAC. Software must also configure these
- * bits when link is forced on a fiber connection.
- *****************************************************************************/
- static int32_t
- e1000_force_mac_fc(struct e1000_hw *hw)
- {
- uint32_t ctrl;
- DEBUGFUNC("e1000_force_mac_fc");
- /* Get the current configuration of the Device Control Register */
- ctrl = E1000_READ_REG(hw, CTRL);
- /* Because we didn't get link via the internal auto-negotiation
- * mechanism (we either forced link or we got link via PHY
- * auto-neg), we have to manually enable/disable transmit an
- * receive flow control.
- *
- * The "Case" statement below enables/disable flow control
- * according to the "hw->fc" parameter.
- *
- * The possible values of the "fc" parameter are:
- * 0: Flow control is completely disabled
- * 1: Rx flow control is enabled (we can receive pause
- * frames but not send pause frames).
- * 2: Tx flow control is enabled (we can send pause frames
- * frames but we do not receive pause frames).
- * 3: Both Rx and TX flow control (symmetric) is enabled.
- * other: No other values should be possible at this point.
- */
- switch (hw->fc) {
- case e1000_fc_none:
- ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
- break;
- case e1000_fc_rx_pause:
- ctrl &= (~E1000_CTRL_TFCE);
- ctrl |= E1000_CTRL_RFCE;
- break;
- case e1000_fc_tx_pause:
- ctrl &= (~E1000_CTRL_RFCE);
- ctrl |= E1000_CTRL_TFCE;
- break;
- case e1000_fc_full:
- ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE);
- break;
- default:
- DEBUGOUT("Flow control param set incorrectly\n");
- return -E1000_ERR_CONFIG;
- }
- /* Disable TX Flow Control for 82542 (rev 2.0) */
- if(hw->mac_type == e1000_82542_rev2_0)
- ctrl &= (~E1000_CTRL_TFCE);
- E1000_WRITE_REG(hw, CTRL, ctrl);
- return 0;
- }
- /******************************************************************************
- * Configures flow control settings after link is established
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Should be called immediately after a valid link has been established.
- * Forces MAC flow control settings if link was forced. When in MII/GMII mode
- * and autonegotiation is enabled, the MAC flow control settings will be set
- * based on the flow control negotiated by the PHY. In TBI mode, the TFCE
- * and RFCE bits will be automaticaly set to the negotiated flow control mode.
- *****************************************************************************/
- int32_t
- e1000_config_fc_after_link_up(struct e1000_hw *hw)
- {
- int32_t ret_val;
- uint16_t mii_status_reg;
- uint16_t mii_nway_adv_reg;
- uint16_t mii_nway_lp_ability_reg;
- uint16_t speed;
- uint16_t duplex;
- DEBUGFUNC("e1000_config_fc_after_link_up");
- /* Check for the case where we have fiber media and auto-neg failed
- * so we had to force link. In this case, we need to force the
- * configuration of the MAC to match the "fc" parameter.
- */
- if(((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed)) ||
- ((hw->media_type == e1000_media_type_copper) && (!hw->autoneg))) {
- ret_val = e1000_force_mac_fc(hw);
- if(ret_val < 0) {
- DEBUGOUT("Error forcing flow control settings\n");
- return ret_val;
- }
- }
- /* Check for the case where we have copper media and auto-neg is
- * enabled. In this case, we need to check and see if Auto-Neg
- * has completed, and if so, how the PHY and link partner has
- * flow control configured.
- */
- if((hw->media_type == e1000_media_type_copper) && hw->autoneg) {
- /* Read the MII Status Register and check to see if AutoNeg
- * has completed. We read this twice because this reg has
- * some "sticky" (latched) bits.
- */
- if(e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) {
- DEBUGOUT("PHY Read Error \n");
- return -E1000_ERR_PHY;
- }
- if(e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) {
- DEBUGOUT("PHY Read Error \n");
- return -E1000_ERR_PHY;
- }
- if(mii_status_reg & MII_SR_AUTONEG_COMPLETE) {
- /* The AutoNeg process has completed, so we now need to
- * read both the Auto Negotiation Advertisement Register
- * (Address 4) and the Auto_Negotiation Base Page Ability
- * Register (Address 5) to determine how flow control was
- * negotiated.
- */
- if(e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_nway_adv_reg) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- if(e1000_read_phy_reg(hw, PHY_LP_ABILITY, &mii_nway_lp_ability_reg) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- /* Two bits in the Auto Negotiation Advertisement Register
- * (Address 4) and two bits in the Auto Negotiation Base
- * Page Ability Register (Address 5) determine flow control
- * for both the PHY and the link partner. The following
- * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
- * 1…
Large files files are truncated, but you can click here to view the full file